英國GRIMM格林進口液氨泵概述： 

          進口液氨泵是英國格林在對同類產品分析研究基礎上，zui新開發出來的產品，主要用于輸送液氨、氨水、甲醇、二甲銨、環氧丙烷、粗苯、環氧乙烷、氯甲烷、異丁烯、丁二烯等性質類似的揮發性液體，廣泛應用于燃氣、石油、化工、制藥、冶金等領域，該泵密封圈和滑片均采用國外特殊配方，耐磨蝕性、韌性、強度非常高，泵殼的材料是高密度耐磨蝕的合金鑄鐵，加工后光潔度高，從而保證了氨液的不泄露，泵的特點就是密封性好，壓力高且穩定。

英國GRIMM格林進口液氨泵工作原理：

          進口液氨泵型式為容積式葉片泵，工作靠葉片離心滑動，流量與軸的轉速有關，定子內曲面采用國內獨創的復合曲線制成，定子與轉子、擋板、葉片組成十個密封腔體，由于定子曲面是復合曲線，當轉子轉動時.進口腔體容積逐漸增大，并形成負壓產生吸力，從而將氨液吸入。當轉子旋轉一定角度后，容積截而逐漸減小，從而將氨液壓出，在吸油腔與壓油腔之間有一封油塊把油腔與壓油腔隔開。葉片靠離心力和兩擋板結構從而與定子內曲而緊密貼合，使泵在額定狀態下正常工作。

英國GRIMM格林進口液氨泵技術參數： 

流    量：2-80m3/h

功    率：1.5-18.5kw

轉    速：600r/min、780r/min

口    徑：25-100mm

壓    差：0.5MPa

溫度范圍：-40℃～40℃

工作壓力：2.0Mpa

材    質：鑄鐵、不銹鋼

英國GRIMM格林進口液氨泵應用領域： 
          主要用于輸送液氨、氨水、甲醇、二甲銨、環氧丙烷、粗苯、環氧乙烷、氯甲烷、異丁烯、丁二烯等性質類似的揮發性液體，廣泛應用于燃氣、石油、化工、制藥、冶金等領域。

UK GRIMM imported liquid ammonia pump summary:

         imported liquid ammonia pump is the latest product developed by Green, UK based on the analysis and research of similar products. It is mainly used to transport liquid ammonia, ammonia, methanol, two methylamine, epoxy propane, Crude Benzol, ethylene oxide, chloromethane, isobutene, butadiene and so on. It is widely used in gas and oil. In the fields of chemical, pharmaceutical, metallurgy and other fields, the seal ring and slider of the pump all use special foreign formula, the abrasion resistance, toughness and strength are very high. The material of the pump shell is high density and wear-resistant alloy cast iron. After processing, the finish of the pump is high, so that the liquid of ammonia is not leaked. The pump is characterized by good sealing, high pressure and stable pressure. Sure.

UK GRIMM imported liquid ammonia pump working principle:

           The type of imported liquid ammonia pump is a volume type vane pump, which depends on the centrifugal sliding of the blade. The flow is related to the rotational speed of the shaft. The inner surface of the stator is made of the original composite curve. The stator is composed of ten sealed cavities with the rotor, the baffle and the blade. Because the stator surface is a compound curve, when the rotor rotates, the volume of the mouth body is driven by the volume. Gradually increase, and form negative pressure to generate suction, so as to inhale ammonia solution. When the rotor rotates a certain angle, the volume is cut down gradually, and the ammonia liquid is pressed out. There is an oil block between the oil suction chamber and the pressure chamber to separate the oil cavity from the pressure chamber. The blade is tightly connected to the stator by centrifugal force and two baffle structure, so that the pump can work normally under rated condition.

UK GRIMM imported liquid ammonia pump technical parameter:

Flow: 2-80m3/h

Power: 1.5-18.5kw

Speed: 600r/min, 780r/min

Caliber: 25-100mm

Pressure difference: 0.5MPa

Temperature range: -40 C ~ 40 C

Work pressure: 2.0Mpa

Material: cast iron and stainless steel

UK GRIMM imported liquid ammonia pump application area:

        It is mainly used to transport liquid ammonia, ammonia, methanol, two methylamine, epoxy propane, crude benzene, ethylene oxide, chloromethane, isobutene, butadiene and so on. It is widely used in gas, petroleum, chemical, pharmaceutical, metallurgy and other fields.