英國GRIMM格林進口臥式單級單吸離心泵概述：
         進口臥式單級單吸離心泵，該泵主要由泵體、泵蓋、葉輪、軸、軸套和懸架等部分組成。泵軸伸出端由兩個滾動軸承支承，軸承用機器油或潤滑脂潤滑。供吸送清水及物理化學性質類似于水的液體。適用于工廠、礦山、城市供水排水、空調，消防和農田排灌之用。
         規格相同的泵因改變葉輪外徑而有不同的性能(在型號后面加上A、B、C等字母表示)。
         本泵結構簡單、性能可靠、體積小、重量輕、抗汽蝕性能好、電耗低、使用維修方便。
         進口單級單吸離心泵通用性廣，全系列共60種規格，但只用四種軸；同一規格的軸、軸承、軸套、軸封、葉輪、緊固件等均能互換；全系列泵的懸架也只有五種。

英國GRIMM格林進口臥式單級單吸離心泵結構說明：
1、臥式單級單吸離心泵為后開式，拆開泵蓋和葉輪時不需拆卸吸水和排水管路。懸架內裝有兩個球軸承，用機器油或潤滑脂潤滑。
2、泵通過彈性聯軸器由電動機直接驅動。
3、渦室、腳、進水法蘭和出水法蘭鑄成一個整體。

英國GRIMM格林進口臥式單級單吸離心泵主要參數： 

流              量：2-1080m3/h
揚              程：5-150m
口              徑：進口直徑：50-300mm
                         出口直徑：32-250mm
轉              速：2900r/min和1450r/min或1480r/min兩級
功              率：1.5-160kw
效              率：24-88%
材              質：鑄鐵、不銹鋼
電              壓：380V、480V、415V、660V
頻              率：50Hz、60Hz
zui  高  轉   速：3500r/min(用于60HZ電源時，葉輪直徑有所減小)
zui高使用溫度：105℃(由機械密封的型號決定)
軸              封：填料密封或機械密封
zui低使用溫度：-10℃
zui大工作壓力：一般為1MPa，如承壓件規定用球墨鑄鐵或鑄鋼制造，可達1.6MPa，請在訂貨時說明

英國GRIMM格林進口臥式單級單吸離心泵適用范圍：
　     供吸送清水及物理化學性質類似于水的液體。適用于工廠、礦山、城市供水排水、空調，消防和農田排灌之用。

UK GRIMM import horizontal single stage single suction centrifugal pump summary:

           import horizontal single stage single suction centrifugal pump, the pump mainly by the pump body, pump cover, impeller, shaft, shaft sleeve and suspension parts. The pump shaft is supported by two rolling bearings, and the bearings are lubricated with machine oil or grease. A liquid that provides water and physical and chemical properties similar to water. The utility model is suitable for factories, mines, cities, water supply, drainage, air conditioning, fire protection and farmland irrigation and drainage.

        Pumps with the same specifications have different properties due to varying impeller diameters (A, B, C, etc.) are added to the rear of the model.

The utility model has the advantages of simple structure, reliable performance, small size, light weight, good anti cavitation performance, low power consumption, convenient use and maintenance.

        The import of single-stage single suction centrifugal pump and wide universality, the whole series of 60 kinds of specifications, but only in four axis; the same specifications of shaft, bearings, shaft, shaft seal, impeller, fastener can exchange; the whole series of suspension pump only five.

UK GRIMM import horizontal single stage single suction centrifugal pump structure description:

1.import  horizontal single stage single suction centrifugal pump for after opening, take apart the pump cover and impeller without removing water absorption and drainage pipe. The suspension is equipped with two ball bearings, lubricated with machine oil or grease.

2.The pump is driven directly by the motor through an elastic coupling.

3.The volute chamber, foot, inlet flange and outlet flange are cast into a whole.

UK GRIMM import horizontal single stage single suction centrifugal pump technical parameters:

Flow rate: 2-1080m3/h

Lift: 5-150m

Caliber: Inlet diameter: 50-300mm

             Outlet diameter: 32-250mm

Speed: 2900r/min and 1450r/min or 1480r/min two

Power: 1.5-160kw

Efficiency: 24-88%

Material: cast iron, stainless steel

Voltage: 380V, 480V, 415V, 660V

Frequency: 50Hz, 60Hz

Maximum speed: 3500r/min (for 60HZ power supply, the impeller diameter is reduced)

Maximum service temperature: 105 ℃(determined by mechanical seal type)

Packing: packing seal or mechanical seal

Minimum service temperature: -10 ℃

Maximum working pressure: generally 1MPa, such as pressure provisions, made of ductile iron or cast steel, up to 1.6MPa, please specify when ordering

UK GRIMM import horizontal single stage single suction centrifugal pump scope of application:

          A liquid that provides water and physical and chemical properties similar to water. The utility model is suitable for factories, mines, cities, water supply, drainage, air conditioning, fire protection and farmland irrigation and drainage.